![]() Keep in mind I am not a mechanic, u are responsible for your own actions. ![]() U can put it in park as soon as the diff cover is in place. Your good to go!īecareful as the truck is in neutral, make sure the wheels are blocked in the front. Your go-to source for car and truck parts, DIY repair advice, and Free Next Day Delivery. Put them in a bit better than finger tight and wait 1hr to fully tighten with a rachet.Īdd 75w90 synthetic (2 litres) Put the drums then wheels back on. But the cover back on, but in a couple bolts at like 11 oclock and 6 and 7 just to hold it in place while u then insert the remaining bolts. Use rtv gasket maker around the diff housing (of course u got the old rtv off as much as possible off both the diff housing and the cover) include the bolt holes taking care to not fill the holes. Return the pin and put the small bolt in. With the c rings back pull the shafts one at a time outward so the rings stay in place. Now remove the pin again so to move the shafts and return the c ring to the shaft. Be gentle, don’t knock the gears too hard. Drive Belt Idler Pull Adj Bolt Kit (4) Driveshaft Flange Bolts (1) Eng Timing Belt Idler Pulley Bolt (1) Engine Connecting Rod Bolt (2) Engine Harmonic Balancer Bolt (3) Engine Oil Pan Bolt Set. Differential Pinion Shaft Lock Bolt (1) Differential Ring Gear Bolt (47). Be careful!Ĭoat the lip of the seal with axle lubricant for protection prior to installing the axle shaft. Bolt Extractor (35) Bolt Length Gauge (1) Bolt Retainer (20) Bolt (423). Install a new axle seal using a block of wood and rubber mallet seating the lip. I used a ruler and measured all the way round matching the other side as the bearing wasn’t removed yet. Install the axle shaft bearing using the old bearing and a block of wood and a heavy hammer. Get Yours Today We have the best products at the. I used a dremel and smoothed a nice sharp ridge Equip cars, trucks & SUVs with 2007 GMC Yukon XL 1500 Differential Pinion Shaft Lock Bolt from AutoZone. Remove any old sealer or burrs from the tube. Remove axle shaft seal from the end of the axle tube with a small pry bar, Remove the axle shaft bearing from the axle tube with Bearing Removal Tool / Slap Hammer with bearing attachment. Use care to prevent damage to axle shaft bearing and seal in the axle tube. Check out free battery charging and engine diagnostic testing while. I would return the pin to keep the gears in place. Order Ford Mustang Differential Pinion Shaft Lock Bolt online today. This enable you to push the axle shaft in and remove the c ring on either side. Remove lock screw and pinion mate shaft from differential case. Dorman Differential Pinion Shaft Lock Bolt 81048 5. Dorman Differential Pinion Shaft Lock Bolt 81048. Buy online for free next day delivery or same day pickup at a store near you. Rotate differential case so pinion mate shaft lock screw is accessible. We have the best Differential Shaft Lock Bolt for the right price. Remove Rear diff bolts using a ½ inch socket, leave the top 2 bolts so the cover doesn’t hit the container catching the oil. Using a rubber mallet, hit around drum and from the back at the lip. This kind of puller puts all the force on the outer race and works 234324342% better than the jaw type.Place transmission in neutral. Tighten the nut keeps the puller in the correct position and the bearing came right out. I clicked on this link Same tools I used, same driver etc Just a better shot of the puller above. Auto zone has a nice aluminum set, much better vs using a socket. Also don't forget to get the bearing driver mandrels. ![]() It took only 3 pulls to get the bearing out the last time i did it. The correct tool looks like this there were a few lengths to choose from in the kit. That took ALOT of force and pulled the roller bearings out of one of the bearings. I used a 3 jaw puller the first time pulling the factory installed bearings. The key was to have the correct length puller, and one that was not already damaged. I had gotten a brand new set of blind bearing pullers along with the slide hammer from Auto Zone.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |